在為您的工作選擇合適的填料后，可使用它來增膠樹脂混合物所需的稠度。特定工作所需的混合物的厚度由添加的填料量控制?；旌弦慌瞿z樹脂的步驟如下：

After selecting the right filler for your job, you can use it to increase the resin mixture to the desired consistency. The thickness of the mixture required for a particular job is controlled by the amount of filler added. The steps for mixing a batch of sizing resin are as follows:

在添加填料之前，將環氧樹脂膠和固化劑混合在一起。使用槳刮擦角落和側面。

Before adding filler, mix epoxy resin adhesive and curing agent together. Scrape corners and sides with paddles.

將測量的填料量添加到桶中。

Add the measured amount of filler to the bucket.

用早先準備的開槽蓋蓋住桶。

Cover the bucket with the slotted cover prepared earlier.

將攪拌器通過蓋子插入環氧樹脂中。

Insert the stirrer through the cover into the epoxy resin.

慢慢啟動攪拌機，逐漸增加速度。

Start the mixer slowly and gradually increase the speed.

上下左右移動混合器，將填料與環氧樹脂混合。當填料開始混合時，厚批量的環氧樹脂將使電機運轉。隨著混合物變得光滑和乳脂狀，這將變得容易。

Move the mixer up, down, left and right to mix the filler with epoxy resin. When the filler begins to mix, a thick batch of epoxy resin will first run the motor. This will become easier as the mixture becomes smooth and creamy.

從桶上取下蓋子和攪拌器。

Remove the lid and stirrer from the bucket.

刮掉桶的角落，將剩余的未增膠樹脂與剩余的批次混合。

Scrape off the corners of the barrel and mix the remaining unsized resin with the remaining batch.

將攪拌器放回原處并短暫攪拌直混合均勻。

Put the stirrer back and stir briefly until the mixture is uniform.

氫氧化鉀廠家提醒您記住將完成的混合物攤開或快速涂抹，以免過熱。

The potassium hydroxide manufacturer reminds you to spread out or quickly smear the finished mixture to avoid overheating.

在混合大批量之前，請考慮質量控制。樹脂和固化劑須充分混合，我們都知道這一點，但在大型項目中時間緊迫時往往會忘記這一點。這不是尋找捷徑的地方，如果您不遵循某些準則，那么再精良的電動攪拌機也將無法彌補。

Before mixing large quantities, please consider quality control. We all know that the resin and curing agent must be fully mixed, but we often forget this when time is tight in large projects. This is not a place to find a shortcut. If you don't follow certain rules, no matter how sophisticated the electric mixer is, it will not be able to make up for it.

為獲得大強度，僅添加足夠的填料以完全彌合表面之間的間隙，而不會下垂或超出接縫或間隙。對于較稠的混合物，在添加填料之前，不要將混合杯填充超過1/3的環氧樹脂膠。

In order to obtain high strength, only enough filler shall be added to completely fill the gap between the surfaces without sagging or exceeding the joints or gaps. For thicker mixtures, do not fill the mixing cup with more than 1 / 3 epoxy resin glue before adding filler.

更多關于這一方面化工產品的信息獲取，您可以來我們網站http://www.hkjzshop.com咨詢了解。

For more information about chemical products in this area, you can visit our website http://www.hkjzshop.com Consultation and understanding.